Category Archives: Template

Posts that contain a template for certain configuration tools, firewall, or whatever.

Juniper ScreenOS Initial Cleanup Config

I still like the Juniper ScreenOS firewalls such as the SSG 5 or the SSG 140. However, they are End of Everything (EoE) and not used at the customers anymore. But they still do their job in basic networking (static/dynamic routing such as OSPF & BGP, IPv6, NAT), basic firewalling (access policies), and IPsec VPN. Hence I am using a couple of SSGs in my lab when playing with routing protocols and so on.

After a factory reset of those firewalls there are some default settings such as zones at a few interfaces and default IP addresses. Therefore I put the following commands together in order to cleanup the default config to have only IP addresses and default routes which is a good starting point for lab configurations. Let’s go:

Continue reading Juniper ScreenOS Initial Cleanup Config

Basic Cisco Configuration

Following is a list of the most common Cisco device configuration commands that I am using when setting up a router or switch from scratch, such as hostname, username, logging, vty access, ntp, snmp, syslog. For a router I am also listing some basic layer 3 interface commands, while for a switch I am listing STP and VTP examples as well as the interface settings for access and trunk ports.

This is not a detailed best practice list which can be used completely without thinking about it, but a list with the most common configurations from which to pick out the once required for the current scenario. Kind of a template. Of course with IPv6 and legacy IP.

Continue reading Basic Cisco Configuration

MRTG/Routers2: Template FortiGate

A few weeks ago I constructed an MRTG/Routers2 template for the Fortinet FortiGate firewalls. I am using it for monitoring the FortiGate from my MRTG/Routers2 server. With the basic MRTG tool “cfgmaker” all graphs for the interfaces are generated automatically. My template is an add-on that appends graphs for CPU, memory, and disk usage, as well as connections and VPN statistics. Furthermore, it implements the ping statistics graph and a “short summary”, which only shows the system relevant graphs.

Continue reading MRTG/Routers2: Template FortiGate

Basic IPv6 Configuration on a FortiGate Firewall

It’s really great that the FortiGate firewalls have a DHCPv6 server implemented. With this mandatory service, IPv6-only networks can be deployed directly behind a FortiGate because the stateless DHCPv6 server provides the DNS server addresses. (This is unlike Palo Alto or Cisco which have no DHCPv6 server implemented.)

However, the configuration on the FortiGate is really bad because nothing of the IPv6 features can be set via the GUI. (And this is called a Next-Generation Firewall? Not only the features count, but also the usability!) Everything must be done through the CLI which is sometimes hard to remember. Therefore I am publishing this memo of the appropriate CLI configuration commands.

Continue reading Basic IPv6 Configuration on a FortiGate Firewall

FRITZ!OS ab 06.23: IPsec P2 Proposals erweitert

Es geht in eine weitere Runde bei den VPNs von und zur FRITZ!Box. Nach den unglücklichen Änderungen in Version 06.20 hat AVM wieder ein paar Phase 2 Proposals hinzugenommen, die komplett ohne Kompression laufen. Somit ist es wieder möglich, die FRITZ!Box im Aggressive Mode VPN-Verbindungen zu diversen Firewalls aufbauen zu lassen. Komisch nur, dass noch nicht alles ganz wie erwartet funktioniert. Hier kommen meine Testergebnisse.

Continue reading FRITZ!OS ab 06.23: IPsec P2 Proposals erweitert

MRTG/Routers2: Template Juniper SSG

Finally, this is how I am monitoring my Juniper ScreenOS SSG firewalls with MRTG/Routers2. Beside the interfaces (that can be built with cfgmaker) I am using my template in order to monitor the CPU & memory, count of sessions & VPNs, count of different kind of attacks, etc.

Continue reading MRTG/Routers2: Template Juniper SSG

MRTG/Routers2: Template Juniper SA/MAG

I am monitoring an (old) SA-2000 cluster of Juniper Secure Access devices with my MRTG/Routers2 system. With the JUNIPER-IVE-MIB I built the configuration file for that monitoring system. In this blog post, I show the graphs generated with MRTG/Routers2 and publish my cfg file as a template.

Continue reading MRTG/Routers2: Template Juniper SA/MAG

MRTG/Routers2: Template Cisco ASA

I constructed a MRTG/Routers2 configuration template for the Cisco ASA firewall which consists the OIDs (graphs) for the interfaces, CPU, memory, VPNs, connections, ping times, and traceroute hop counts. With only four search-and-replace changes as well as a few further specifications, the whole SNMP monitoring for that firewall is configured.

Continue reading MRTG/Routers2: Template Cisco ASA

IPsec Site-to-Site VPN Cisco Router <-> AVM FRITZ!Box

Der Titel sagt eigentlich schon alles: Es geht um das Herstellen eines S2S-Tunnels zwischen einem Cisco Router (statische IPv4) und einer FRITZ!Box (dynamische IP). Ich liste nachfolgend alle Befehle für den IOS Router sowie die Konfigurationsdatei für die FRITZ!Box auf. Für eine etwas detaillierte Beschreibung des VPNs für die FRITZ!Box verweise ich auf diesen Artikel von mir, bei dem ich zwar ein VPN zu einem anderen Produkt hergestellt habe, aber etwas mehr auf die Schritte der Konfiguration eingegangen bin.

Continue reading IPsec Site-to-Site VPN Cisco Router < -> AVM FRITZ!Box

MRTG/Routers2: Template MessPC Ethernetbox

Eine sehr praktische Variante, möglichst viele Sensoren übers Netzwerk abzufragen ohne dabei viel basteln zu müssen, ist die Ethernetbox von MessPC. Man kann sie zum Beispiel mit mehreren kombinierten Temperatur/Luftfeuchtigkeits-Sensoren bestücken. Die Auswertung erfolgt am besten über ein zentrales Monitoring-System.

Auf der Homepage von MessPC befindet sich zwar eine kleine Dokumentation für die Verwendung von MRTG, allerdings wird dort ein zusätzliches Skript vorgestellt, was dank der Verwendung von SNMP ja gar nicht nötig ist. Deswegen poste ich hier mein Template von einem MessPC mit zwei Kombisensoren für Temperatur/Luftfeuchtigkeit, welches für die Verwendung mit MRTG und Routers2 gemäß meiner Installation geeignet ist. Mit nur drei Suchen-und-Ersetzen Durchläufen hat man das Template angepasst.

Continue reading MRTG/Routers2: Template MessPC Ethernetbox

Measuring Temperatures with PCsensor’s TEMPerHUM Sensor

I am always interested in capturing real values via hardware devices in order to generate the appropriate graphs with my monitoring system. Of course, the outside temperature in our city was at the pole position for such a project. Therefore I ordered a few temperature/humidity sensors from PCsensor (via eBay), plugged them via USB on my Raspberry Pi (Raspbian Linux), and queried them via SNMP from my MRTG/Routers2 monitoring server. Here is the whole story:

Continue reading Measuring Temperatures with PCsensor’s TEMPerHUM Sensor